Like, if unit is off, you can to press:
- IN + PWR - to full selftest of unit (screen test, keypad test, NMEA test)
- OUT + PWR - to serial port test
- ESC + PWR - to burn-in process
- LIGHT + ENTER + RWR - tp uploading of new firmware
- NAV + PWR - to call Service Function window (see below)
- NAV + MENU + PWR - to force power off, equal remove batteries.
- GOTO + OUT + POWER - clear memory and set all settings as default.
- GOTO + IN + POWER (hold 10 sec) - reset for eXplorist XL
Service functions:
If while unit is "power off", press and hold NAV key then press PWR key, or if uint is already on,
press MENU key then press right-left-right-left arrows, then on center of screen the service function
windows with text "00" will appears. With help of arrows you can to change "00" to number of any other
service function, then press ENTER.
N FUNCTION
---- ---------------------------------------------------------------
0 Show Information about firmware version and unique ID of unit
1 Show statement of corellator chahels
2 Show memory dump and registers after last units failure
3 Turn WAAS on / off
5 Clear ephemerides
10 Turn unit off
15 Full selftest (like IN + PWR)
16 Serial port test (like OUT + PWR)
17 Burn in (like ESC + PWR)
20 Show stetement and calibrations
26 Waiting for remote assistance
27 Waiting for remote assistance
30 Clear memory menu
31 Clear XO parameters (may be usefull, if unit can't to find any satallite)
32 Clear all memory prompt
33 Verify basemap
38 Interface language select
40 Set serial port boud rate
41 NMEA settings
70 Waiting for remote assistance
71 Create some PIOs for testing
72 Screen frame rate
75 Simulator settings
78 Service report
82 Compensation offset settings. (DO NOT change, if you don't know, what is compensation!)
90 XO and A-D settings. (DO NOT change, if you don't know, what is XO and A-D!)
92 Waiting for remote assistance
93 Rename of basemap
94 Report of serial flash-memory using
95 Serial flash-memory erasing. (basemap after call of this function will be ERASED!)
96 Report about structure of serial flash-memory
97 Clear secondary SMC basemap.
98 Basemap upload mode
99 Firmware upload mode (like LIGHT + ENTER + PWR)
Los códigos 33 y 93 a 97 no funcionan en E100
(Traducción rápida:Hágase aquel responsable del mal uso de los códigos o entendimientos de los mismos. Yo los tengo probados en mi Xplorist y funcionan correctamente.
con el aparato apagado pulsar la tecla NAV y a continuación PWR. Se encenderá, pulsar tecla MENU y las flechas del cursor enel siguiente orden, Dcha, izqda, dcha, izqda. en al pantalla aparecera dos ceros "00" y nuevamente con las flechas del cursos puedes seleccionar el número de la lista de abajo, le damos a ENTER para proceder.)
Al igual que, si la unidad está apagada, puede pulsar:
- IN + PWR - a SelfTest completa de la unidad (prueba de pantalla, teclado de prueba, prueba NMEA)
- OUT + PWR - para probar el puerto serial
- ESC + PWR - para quemar el proceso.
- LUZ + ENTRAR + RWR - TP carga de nuevo firmware
- NAV + PWR - para llamar a Servicio de función de la ventana (véase más abajo)
- NAV + MENU + PWR - para forzar apagar la alimentación, como quitar las pilas.
- IR A + OUT + POWER - borrar la memoria y establecer todos los ajustes por defecto.
- IR A + en + POWER (mantener 10 seg) - reset para eXplorist XL
0 Mostrar información sobre la versión del firmware y el identificador de la unidad
1 Declaración Show de chahels corellator
2 Mostrar volcado de memoria y registros después de las último fracaso/error
3 WAAS Turn on / off
5 limpiar/borrar efemérides
10 Apague la unidad
15 SelfTest completa (como en + PWR)
16 prueba del puerto-serie (como OUT + PWR)
17 Burn in (como ESC + PWR)
20 Mostrar stetement y calibraciones
26 asistencia remota
27 asistencia remota
30 menú Borrar memoria
31 abierto parámetros XO (puede ser útil, si la unidad no puede encontrar ningún satélite)
32 Borrar toda la memoria del sistema
33 Verificar el mapa base
38 Seleccionar de interfaz de idioma,
40 Establece el puerto serial tipo Boud
41 ajustes de NMEA
70 asistencia remota
71 Crear una PIO para las pruebas
72 Tipo de marco de la pantalla
75 ajustes de Simulador
78 Informe de servicio
82 Ajustes de Compensación. (NO cambie, si no sabes, cuál es la compensación!)
90 XO y A-D configuración. (NO cambie, si no sabes, lo que es XO y AD!)
92 Lugar para asistencia remota
93 Cambiar el nombre del mapa base
94 Informe de la memoria Flash utilizado en serie
95-memoria flash de serie borrado. (mapa base, tras la ejecución de esta función se borrarán)
96 Informe sobre la estructura de la memoria Flash
97 Borrar mapa base SMC secundaria.
98 modo de mapa base de carga
99 modo de subir el Firmware ( LIGHT + ENTER + PWR)
OJO, mi inglis no es muy pallá ehhh . . . pero más o menos creo que lo tengo.
Enjoy